Pinetree

• 목록
• 답변
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are your primary line of defense against unauthorized access to your home. The locks may need to be replaced because of signs of wear and tear or other events like moving into a new home or a burglary.

To begin, you must determine your cylinder size by measuring the distance between the adjustment screw and the middle of the cylinder knob. This measurement will allow you to purchase the appropriate lock.

Deadbolt

Installing a deadbolt can be a excellent way to protect your door from intruders. When the bolt is extended into the strike plate of the doorframe it makes it much more difficult for an intruder to get through the door. A single-cylinder deadbolt is activated using a key on the exterior, and a thumb-turn piece situated inside. Deadbolts can only function when it is properly installed.

First, you'll need to determine if the door already has a hole to install a deadbolt or if it needs to be bored out. With the template included with the lock installation kit mark the location of the deadbolt hole on the door's surface. Use a tape measure to determine the height of the deadbolt. Mark this high point on the door's edge. Use the speedsquare to draw a straightline across the mark that you made for the bolt hole.

Then using an electric drill, bore through the hole until it is on the opposite side of the door. This could take a while. Then, sand down the hole and along the edge of the door until it is smooth. At this point, it's a good idea to stain or paint your door.

Remove any screws that are visible from the deadbolt. This will reveal the back and front door lock replacement cost assemblies of the deadbolt, as well as the internal bolt. Then, unscrew the bolt and replace door lock (please click the following web site) it with a new bolt that matches your door hardware. It is necessary to remove the bolt from the setplate. After that then you need to chisel out the area for the strike plate that is on the door frame.

If your strike plate isn't aligned properly It's likely that the previous installer didn't mortise it correctly or a weatherstripping came along and changed the strike position. You will need to re-mortise the strikeplate and possibly even the deadbolt to fix the issue. Close and lock the deadbolt after you've completed this step. Test the deadbolt by closing it and locking it once the bolt has been extended into the strike plate.

Knob

If the knob on your door wears out it could make your home or business less secure. It could also make opening or closing the door more difficult, which is why it is a good idea for you to replace lock upvc door the knob. It shouldn't take longer than 30 minutes. Use a screwdriver or pliers to remove any knobs or handles. Be cautious not to harm other components of the door.

Spray WD-40, or a different dry lubricant, onto the mechanism of your door knob before you begin. This will let the new lock to slide smoothly when you turn it. To ensure that it operates properly it is important to select the right knob and handle to match your existing doors. If you don't already have a matching doorknob then you'll have to purchase a new one.

To begin the replacement process, look over the knob or handle to determine what screws are holding it in place. If there are no screws then you can use the screwdriver to wedge the cover plate in between the screws plate hidden behind it.

After you have removed the knob examine it for indications of damage and rust. If the knob has any dents or marks, you'll have clean it. Otherwise it shouldn't require any major work.

Install the new knob. You must first study the two knobs to make sure that you've selected the right one for the door. You'll need to choose one with an extended rod that will interlock with the rod mechanism of the second knob. Once you've put the new knob over the door's hole and then carefully slide it into the latch.

Thread the latch plate screws downwards and then test the spring by pushing down on it several times. The latch should spring up each time. Then, put in the new knob and connect it to the rod mechanism on the previous knob. Thread the long screws of the doorknob's interior through the holes for the cylinder on the exterior knob and secure it in place.

Latch

A latch is a metal piece that extends out into the doorjamb in order to hold it closed. The latch can be operated by a knob or handle on the interior of the door lock replacement near me, or by a thumb-turn on the outside. Deadbolts can be used to secure a latch and prevent burglars from piercing the glass of the door. It can also protect against the accidental or deliberate closing by children or animals. You can choose to install the latch using either a single-cylinder deadbolt, or a double-cylinder deadbolt, depending on the level of security.

Installing a latch requires the same steps similar to installing a deadbolt however there are some differences. First, you must measure the setback of the doorjamb with an instrument to make sure the new lock will fit. The setback is measured from the edge of doorjamb up to the middle of the hole for the latch plate. The standard setback is 2 3/8 to 2. 3/4 inches. If you have a larger setback, you may have to purchase a larger latch from a hardware store or locksmith.

The next step is to drill an edge bore hole in the doorjamb to accommodate the latch plate. Use a chisel and cut the mortise of the latch. Make sure the hole's depth is sufficient for the faceplate to be in line with the doorjamb. Put the strike plate into place to make sure it is positioned correctly.

If the strike is set too high, the door may be pushed into or pressure put on it using a crowbar or tire iron. This could also cause cracks in the doorjamb. This can be corrected by drilling a new hole in the doorjamb, and chiseling the core out of the hole that was previously made.

Installing the new strike plate is the final step. This can be done by screwing the new plate into the screw holes that are already in place. Then apply wood putty to fill in the old screw holes and the bolt hole that is not used. After the putty has dried, sand it smooth for a professional finish.

Strike

The piece of metal that connects the deadbolt and latch when the door is closed is an electric strike. It is an essential part of the lock's overall security because it prevents the door from opening and gives additional resistance to force or kick. If a door is equipped with an electronic strike, it will be opened only with an entry key and a control unit that regulates the electrical impulses.

In the past, putting in an electronic strike was as simple as cutting a piece of a doorjamb, which would let the latchbolt of a cylindrical lock from the pocket inside the strike. This is not only undesirable, but also exposes the mechanism for the latchbolt and keeper to unauthorized users.

Recently, several electric strikes manufacturers have come up with a "No Cut" type of strike that does not require a cutout in order to operate. These strikes have a unique design to allow the keeper and latchbolt to slide into the strike pocket without marring the doorjamb faceplate.

The strike has an internal ramp that lifts the latchbolt as well as the keeper when it receives the signal of a reader. The latchbolt and keeper are lifted higher on the ramp thanks to the retraction. When the door is closed the deadbolt is retracted and the latchbolt retracts into the keeper.

Installing an electric strike is an easy process, particularly in the case of replacing a strike on an existing door. However, if you are upgrading to an electric strike in an access control system, you will have to ensure that your new system is compatible with the type of lock you have installed. Also, you must ensure that the strike is properly connected to your access-control system and is set up to operate in a fail-safe way.

Upgrade your strike plates with heavy duty strike plates to block unauthorised entry. These plates use four to six three-inch screws instead of the two, three-fourth inch screws commonly used in standard strikes. The longer screws make breaking the frame to reach the thumb turn piece on a single deadbolt for a cylinder more difficult.