Pinetree

• 목록
• 답변
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About boarding up doorway emergency boarding up cost a Door

Boarding up a door is one way to protect vacant investment properties from the elements. While it may not stop all destruction, it can help avoid certain problems that come with severe storms.

Boarding up windows and doors can deter trespassers and vandals as well as squatters. Placing plywood boards over doors and windows can be time-consuming and expensive.

Measure the Door

First, you'll need a tape measure. It is a good idea to keep a ladder or a chair nearby in case you need to see more clearly the top of the frame. If you have to make use of these tools, be sure to wear gloves and safety glasses.

Once you have the measuring tool, start by taking the door's width measurement. You can do this by running the tape measure horizontally across the door. Make sure to remove any other door components such as a door sweep, from the measurement. Then, you can measure the height by measuring from the floor to the existing sill plate or the lintel. It is important to measure in more than one location especially for older doors, as they may not be an exact rectangle. If the measurements vary take the largest number.

After you've logged the measurements of height and width then you'll have to determine what size boarding up and burglary repairs you need for the frame. Ideally, it should be 2 inches wider than the door and 1 inch thicker than the door. 2'' higher. This will allow enough space to shim the door and frame to fit.

It's a good idea to remove the casing or trim around the jambs of your door to see the studs. This will allow you to measure the exact gap between the studs of the frame and the edge.

After taking off the trim, take a measurement of the width of the door frame using a tape measure. The frame should be measured at three different places and use the smallest measurement. Also, you should measure the frame's height from top to bottom on both sides. Make use of the shortest measurement for your door's width.

If you're having difficulty with these measurements It's a good idea at this point to consult an expert and ask them to visit your home to do the measuring for you. They will tell you what size and type of door you'll need and how to prepare your frame to accommodate a replacement door.

Plywood can be cut into pieces

A door frame is typically composed of thin boards or studs that create a hollow space around the door. Two hinges are attached to the studs and keep a typical door in position. This means that if you want to restore the door, it is necessary to remove the door from its hinges over the course of a few days. To stop insects from entering your home and to secure the door's opening, a straightforward method to board the door is to put plywood inside the opening. This is a simple process without having to nail or screw the plywood to the door frame.

Plywood is cheap, easy to work with and looks great when it is finished. It is the ideal material to make a temporary solution for a problem where you're required to remove an existing door to refinish or install an entirely new one. It is also useful to secure the opening of a room that is being renovated, like an unfinished basement, or a construction site.

For a wall constructed of plywood, start by taking measurements of the width and height of the door opening. Note the measurements using an utility knife and a metal straight edge such as the drywall or metal square. Then, draw a chalkline across each line to mark the area to cut. Then, use a circular saw to cut the plywood to the desired size.

It is essential to protect both your ears and eyes when cutting plywood. If possible wear safety goggles and earplugs when working. It is also important to use a sharp blade with a lot of teeth, which will permit you to cut quickly and without any tear-out. Utilize a small piece of wood to guide the blade. Hold it about a hair's distance from the mark when cutting.

Attaching a pair or short braces on each side is a great method to secure the plywood in place without screwing it into studs. Put one brace on the side that is inside and the other one on the outside of the door. Place a 1-1/2-inch deck screws in each hole and tighten by using an open-end ratchet.

Fix the Plywood

It's now time to connect the frame to the panel after you have the plywood sheet cut to the right dimensions and the holes for the rails and stiles of the door frame are predrilled. This is a simple task that doesn't require advanced carpentry skills, as long as you use the right tools and follow the correct procedure.

Start by setting up a worktable near the doorway with two sawhorses and 2-by-4 framing lumber at each end of the table. Utilize the marks you made during the measurement procedure to guide you in cutting the plywood. Utilize a utility knife and a metal straight edge to cut the lines. This will act as a guide for the saw blade, and prevent splintering of the plywood when you cut it.

Put on eye protection and cut along the scored lines using a circular saw or table saw fitted with a fine-tooth blade. Then, sand the edges of the plywood panel with 120-grit sandpaper. This will smooth the panels and remove any burrs from the saw cuts. After sanding, apply a wood sealer and let it dry according to the manufacturer's instructions.

Install the hinges on the door frame. If you're using T hinges, make holes in the outside of the door to accommodate the strap parts of the hinges. Then, put the hinge's outside on its mark and screw it onto the frame using an screw gun. Repeat the process on the inside of the door for each of the remaining hinges, being cautious not to tighten too much on any of them or the panel may shift.

If you have an outside hinged door with only one T you can make it easier to lock and close with a chain lock by putting a piece wire through the loops of the outside hinges. Bend a piece of tie wire in half, and put it through the two holes on the outside of the door. Then twist the wires to pull them tight and fix the door.

Install the Plywood

With the measurements you made and place the plywood into the door opening. Change the frame's header (top) and the sill. Use a level and ensure that there's no slop between the header and Boarding up windows and doors sill. If the level isn't perfect, put another shim in the place where needed and continue this process until you get the sill and header to be in a straight line.

Once the plywood is in the frame, fasten it with stainless steel hinge bolts and wings nuts. It's a good idea to utilize a screw gun that has a hex-head attachment to keep the head from being stripped of the screws.

If you live in a house with studs that run along the length of your doorway, you can drill hanger bolts into every framing piece. This is much easier than using a drywall cutting tool to create the hole.

After putting the plywood in place, take measurements of the width and height of the door opening. If necessary, trim the bottom of the plywood to fit the dimensions of your door frame. Cut two pieces of 1-by-6 framing lumber for braces to attach across the upper and lower edges of your door. Cut along the lines that are marked on your plywood with circular blades with teeth that are finely-toothed. Wear eye protection. Take any splinters out of the cuts by using an the sanding block.

After you have the two braces in place, nail each one to the plywood with pairs of 2-inch finishing nails. When you're finished, counter sink the heads of all the nails. Seal the braces and the plywood with a quality wood sealer, such as this wipe on polyurethane from Minwax.

If your door is too large You can either put in decorative molding to fill the gap between your jamb and door, or you can alter the size of your opening. In many instances, however it's cheaper and easier to simply buy the door. This will also take away any issues you may have experienced with the door you originally purchased if it was damaged and didn't fit for the opening.