Pinetree

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

As time passes, the handles on your doors will get worn out and will require replacement. When replacing them, it is crucial that the new handles match the critical dimensions of the old handle.

The top screw position, the lever and the keyhole dimensions are the three measurements that you need to verify. Use the size guide to help with this.

Inline Lever/Lever

A lever handle is a modern victorian door handle handle that is designed to fit new or replacement doors. This kind of door handle is available in a wide range of styles and finishes. A variety of manufacturers provide this type of handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are constructed of durable materials and are suitable for multi point lock doors which require a robust design. The handles are inline and run off the same spindle and screw fixings. They are easily installed on existing or new uPVC/Composite doors.

The handle can be adjusted and angled to fit all users. The handle has been endurance-tested to 200 000 cycles. This helps ensure that the quality of finish and performance over time. The sprung lever is adjustable to fit a wide range of locks. This is particularly useful in doors that are narrower, where the cylinder is situated further back from the door. A shorter lever can be used for doors with a latch that can be opened by the thumb on the inside.

Lever Pad

The lever pad upvc handle differs from the lever handles commonly found on doors. These handles are operated by a single spindle or by two spindles, either inline or offset. They are typically utilized on UPVC doors with double glazing handles glazing and come in a variety of finishes & variations.

The handles have been tested to a minimum of 200 000 cycles and are available in several finishes, including White, Silver, Chrome & Gold. The finish is compliant with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, giving the handle a high level of durability and performance for its intended use.

All of the UPVC handle lever pad styles come with a spindle and screws that allow them to be put on a new or existing uPVC door. The backplate fixing centres of 211mm allow for a wider size handle that is often a benefit when replacing a damaged or worn multi point door lock mechanism. The handle levers are spring-loaded, thereby solving the issue of handles hanging out of the horizontal position when not in use.

When selecting the replacement UPVC handle and spindle it is crucial to match the dimensions of the PZ on both the multipoint lock and the uPVC door. This measurement is often called the "handle centre" or "cylinder centres and is an essential aspect of matching up the appropriate handles.

Once you have the proper PZ size, you'll need to ensure that the handle lever pads and push pads are of a appropriate shape to accommodate the American with Disabilities Act (ADA) compliant handles that you need for your doors. These are usually square or round with an internal lever, and an external push pad.

The majority of the UPVC Lever Pads that we sell are spring-loaded. This means that they return to a horizontal position when not being used instead of hanging, and possibly being stuck in the frame. This prevents drafts and cold air from entering a property. The majority of UPVC lever pad style handles come in both left and right handed models that allow them to be put on either side of doors.

Euro Cylinder

Cylinder locks are usually found on uPVC doors, but they can also be found on other types of doors. The cylinder lock is operated by a key which unlocks the cylinder case. This reveals pins that can be aligned to those inside the lock, and permit them to turn the revolving camera, thereby opening the door. Euro cylinders are available with up to six pins. External and internal doors require different levels of security.

The selection of a cylinder is crucial. It's dependent on the use that your doors and handles receive. External doors, for instance should be equipped with cylinders with greater security while internal doors can be secured using a standard cylinder. Certain cylinders come with extra features that can improve security, such as anti-drill or anti bump properties.

To ensure that the euro cylinder is the correct size for your aluminium door handle, it should be measured correctly. The cylinder should be measured from the hole in the center of the fixing screw to the end of the cylinder and the thumb turn if you have one. If you cannot measure using the lock in a fixed position, you can take it out of it. It is essential to not have a extension of the cylinder beyond the handle or escutcheon. This can make it vulnerable to snapping lock attacks.

Most newer cylinders have been constructed with anti-drill and bump resistance features included in their design. They are designed to minimize attacks by forcing cylinders to turn in a new direction. This will help deflect the attack, and protect your door.

There are also cylinders that are made to resist snapping. This is a common attack on cylinders. A specific tool is used to break the lock's break line and then the front of cylinder is snapped off. This is a quicker and easier way to gain access than a multipoint locking system. It also leaves no evidence of the break-in which can hinder insurance claims.

Spring Cassette

The spring cassette is located within the base of your door handle backplate providing a sprung solution to return the multipoint lock handles back to their normal position after use. In the past, a lot of these types of handle did not have a spring integrated into them, and without it they are more likely to slide or 'drop' once the locking mechanism is disengaged. Adding this simple component is one of the most effective ways to fix this issue and is an effective way to keep your upvc doors from getting stuck in the open or closed position, as these aren't always easy to manually close by hand.

These spring cassettes are specially designed to be used with sprung multipoint locks, they will not fit multipoint handles that are not sprung and you will require a hole specifically cut in your backplate to allow these to fit (please check the image for a technical diagram). They are a replacement for existing broken or missing cassettes in the bifold door handle replacement handle backplate of various kinds of uPVC doors. They are fitted with a square cut out which allows for an 8mm spindle to be used and are sold as a set.

These spring cassettes are a great value-for-money way to fix the problem of door handles that are sagging. They are easy to fit and will extend the life span of your uPVC doors. For more information on our wide range of uPVC accessories and spares, contact us today. in touch with our team. We are always happy to offer expert advice and support you.